【 Print Head 】
Mimaki Printer Parts JV22
ID: 1000002201
Ink cannot be fired correctly and results in missing dot when the head is broken or reaches its life. When the head is electrically broken, it sometimes prints unnecessary lines.

【 Main Board 】
Mimaki Printer Parts JV22
ID: E103537 E102051

【 1394 board 】
Mimaki Printer Parts JV22
ID: E103898 E102161
1394 Firewire Board E103898 E102161 If you have a problem of the computer not being able to see your JV3 or JV4 printer and you have replaced the firewire card in your computer. If error 23 happened when you install 1394 board, please double check the data cable that is connected

【 Carriage Board 】
Mimaki Printer Parts JV22
ID:

【 IF Board 】
Mimaki Printer Parts JV22
ID:

【 Cap Sensor ASSY 】
Mimaki Printer Parts JV22
ID:

【 CR Belt 】
Mimaki Printer Parts JV22
ID:

【 Small Damper 】
Mimaki Printer Parts JV22
ID: 11959109
Ink is not supplied to the head properly. As a result, the white or dark lines appear in the printing image, or printing becomes scratchy.

【 Oversized Damper with adapter screws 】
Mimaki Printer Parts JV22
ID: 11959109
Ink is not supplied to the head properly. As a result, the white or dark lines appear in the printing image, or printing becomes scratchy.

【 O Ring 】
Mimaki Printer Parts JV22
ID:
The use of an o-ring as a seal is mainly to prevent the transfer of fluid (liquid, solid or gas) between two or more regions. The components of the seal are the o-ring itself and the contact surfaces. The elastomeric o-ring relies on a compressive force acting on the o-ring to prevent the transfer of fluid between regions. Successful seal design ensures adequate seal compressive force while optimizing the destructive stress acting on the o-ring as a result of the compression or of the environment.

【 Cap Top 】
Mimaki Printer Parts JV22
ID: 10002794
Ink is not supplied to the head properly. As a result, the white or dark lines appear in the printing image, or printing becomes scratchy.

【 Pump 】
Mimaki Printer Parts JV22
ID: 7576340000
Cleaning is not performed efficiently because ink is not sucked well. As a result, white or dark lines appear in the printing image.

【 PRINT HEAD MANIFOLD 】
Mimaki Printer Parts JV22
ID:
Cleaning is not performed efficiently because ink is not sucked well. As a result, white or dark lines appear in the printing image.

【 Scan Motor 】
Mimaki Printer Parts JV22
ID: 7876709010
When the Motor is broken or reaches its life, the Motor cannot obey the order from the CPU and it results in the Motor Error.

【 Print Head Cable 21 Pin 9in/23cm 】
Mimaki Printer Parts JV22
ID: 23475206
When there is a bad contact with the Flexible cable connected to the head, or there is a cut line in the Flexible cable, the head doesn't work properly.

【 Wiper 】
Mimaki Printer Parts JV22
ID: 11379105
Wiper cannot remove the foreign substances stuck on the surfaceof the head. In that condition, ink is not fired properly and thewhite or dark fine lines appear in the printing image.

【 45 DEGREE SUPER HARD BLADES 】
Mimaki Printer Parts JV22
ID: CG 75 130 160 SRII 60SR Blade 160 SRII 60SR Blade

【 Cutter BLADES 】
Mimaki Printer Parts JV22
ID: CG 75 130 160 SRII 60SR Cutter Knife Blade

【 Pump Tube Solvent Resistance OD=4mm ID=2mm 】
Mimaki Printer Parts JV22
ID:

【 Ink Tube OD=3mm ID=2mm 】
Mimaki Printer Parts JV22
ID:
Ink Tube Solvent Resistance

【 Syringe 】
Mimaki Printer Parts JV22
ID:

【 Encoder Sensor 】
Mimaki Printer Parts JV22
ID:

【 Encoder Strip 160 】
Mimaki Printer Parts JV3 160
ID:

【 Encoder Strip 250 】
Mimaki Printer Parts JV3 250
ID: