【 Print Head 】
Mimaki Printer Parts CJV30
ID: 1000002201
Ink cannot be fired correctly and results in missing dot when the head is broken or reaches its life. When the head is electrically broken, it sometimes prints unnecessary lines.

【 Damper 】
Mimaki Printer Parts CJV30
ID: 11959109
You need to change your dampers if Ink is not supplied to the head properly. As a result, the white or dark lines appear in the printing image, or printing becomes scratchy.
Our Mimaki CJV30 Dampers are solvent resistant. It is recommend that you change CJV33 dampers and O-rings with every head change. Dirty dampers impede the flow of ink and you'll get frequent drop-outs, missing jets and ink starvation. Eventually, neglected dampers will damage to the printhead because of overheated jets. If you have a problem where the ink constantly gets drained out of the dampers and ink lines – back into the cartridge, you have an air leak. Replacing the O-Ring and screw usually cures this problem. Remember that each printhead uses 2 dampers!

【 Cap Top 】
Mimaki Printer Parts CJV30
ID: 10002794
Ink is not supplied to the head properly. As a result, the white or dark lines appear in the printing image, or printing becomes scratchy.

【 Ink Pump 】
Mimaki Printer Parts CJV30
ID: 7576340000
Cleaning is not performed efficiently because ink is not sucked well. As a result, white or dark lines appear in the printing image.

【 Print Head Cable 31 Pin 14"/36CM 】
Mimaki Printer Parts CJV30
ID: 23475206
When there is a bad contact with the Flexible cable connected to the head, or there is a cut line in the Flexible cable, the head doesn't work properly.

【 Print Head Cable 34 Pin 14"/36CM 】
Mimaki Printer Parts CJV30
ID: 23475206
When there is a bad contact with the Flexible cable connected to the head, or there is a cut line in the Flexible cable, the head doesn't work properly.

【 Print Head Cable 30 PIN 9'9"/297CM 】
Mimaki Printer Parts CJV30
ID: 23475206
When there is a bad contact with the Flexible cable connected to the head, or there is a cut line in the Flexible cable, the head doesn't work properly.

【 Print Head Cable 50 PIN 10'/304CM 】
Mimaki Printer Parts CJV30
ID: 23475206
When there is a bad contact with the Flexible cable connected to the head, or there is a cut line in the Flexible cable, the head doesn't work properly.

【 Wiper 】
Mimaki Printer Parts CJV30
ID: 11379105
Wiper cannot remove the foreign substances stuck on the surfaceof the head. In that condition, ink is not fired properly and thewhite or dark fine lines appear in the printing image.

【 45 DEGREE SUPER HARD BLADES 】
Mimaki Printer Parts CJV30
ID: CG 75 130 160 SRII 60SR Blade 160 SRII 60SR Blade

【 Cutter BLADES 】
Mimaki Printer Parts CJV30
ID: CG 75 130 160 SRII 60SR Cutter Knife Blade

【 Pump Tube Solvent Resistance OD=4mm ID=2mm 】
Mimaki Printer Parts CJV30
ID:
9.95USD/Foot

【 Ink Tube OD=3mm ID=2mm 】
Mimaki Printer Parts CJV30
ID:
9.95USD/Foot
Ink Tube Solvent Resistance

【 Syringe 】
Mimaki Printer Parts CJV30
ID:

【 Encoder Sensor 】
Mimaki Printer Parts CJV30
ID:

【 Encoder Strip 60 】
Mimaki Printer Parts CJV30 60
ID:
This line encoder is for CJV30 60 printer with width scale 1100.
You'll need to make a small hole in each end of this Mutoh Encoder Strip to attach to the screw or spring and cut it down to match the size of the old one. However, it is a good alternative solution to using Lavaink Encoder Strip at 30% the price than using the original encoder strips.
The warranty will be void if Lavaink label at this encoder strip was removed!!! Use sharp knife to cut a small rectangle.
Please try this cut at the same end of encoder strip because I give you enough long to cut.
After you are confident, and you can cut the real hole.
Should keep the same length as your old one.

【 Encoder Strip 100 】
Mimaki Printer Parts CJV30 100
ID:
This line encoder is for CJV30 60 printer with width scale 1550.
You'll need to make a small hole in each end of this Mutoh Encoder Strip to attach to the screw or spring and cut it down to match the size of the old one. However, it is a good alternative solution to using Lavaink Encoder Strip at 30% the price than using the original encoder strips.
The warranty will be void if Lavaink label at this encoder strip was removed!!! Use sharp knife to cut a small rectangle.
Please try this cut at the same end of encoder strip because I give you enough long to cut.
After you are confident, and you can cut the real hole.
Should keep the same length as your old one.

【 Encoder Strip 130 】
Mimaki Printer Parts CJV30 130
ID:
This line encoder is for CJV30 60 printer with width scale 1850.
You'll need to make a small hole in each end of this Mutoh Encoder Strip to attach to the screw or spring and cut it down to match the size of the old one. However, it is a good alternative solution to using Lavaink Encoder Strip at 30% the price than using the original encoder strips.
The warranty will be void if Lavaink label at this encoder strip was removed!!! Use sharp knife to cut a small rectangle.
Please try this cut at the same end of encoder strip because I give you enough long to cut.
After you are confident, and you can cut the real hole.
Should keep the same length as your old one.

【 Encoder Strip 160 】
Mimaki Printer Parts CJV30 160
ID:
This line encoder is for CJV30 60 printer with width scale 2100.
You'll need to make a small hole in each end of this Mutoh Encoder Strip to attach to the screw or spring and cut it down to match the size of the old one. However, it is a good alternative solution to using Lavaink Encoder Strip at 30% the price than using the original encoder strips.
The warranty will be void if Lavaink label at this encoder strip was removed!!! Use sharp knife to cut a small rectangle.
Please try this cut at the same end of encoder strip because I give you enough long to cut.
After you are confident, and you can cut the real hole.
Should keep the same length as your old one.